Talk:Digital micromirror device

Electronics Low‑importance

	Electronics portal This article is part of WikiProject Electronics, an attempt to provide a standard approach to writing articles about electronics on Wikipedia. If you would like to participate, you can choose to edit the article attached to this page, or visit the project page, where you can join the project and see a list of open tasks. Leave messages at the project talk pageElectronicsWikipedia:WikiProject ElectronicsTemplate:WikiProject Electronicselectronic articles
Low	This article has been rated as Low-importance on the project's importance scale.

Merge from Digital Micromirror Device[edit]

This article (Digital micromirror device) is the correct capitalization according to WP:NC, but the article at Digital Micromirror Device is much more complete, and should be merged here. Comments? --Bob Mellish 16:34, 16 December 2005 (UTC)[reply]

No objections, so I moved the page to the correct title & merged what content was there. --Bob Mellish 23:23, 26 December 2005 (UTC)[reply]

physics[edit]

"Because of the small scale, hinge fatigue is not a problem" What is the physical reason for this?--84.188.176.54 22:54, 12 February 2006 (UTC)[reply]

Fatigue is averted because the physics of dislocations movement (source of fatigue failure) is not the same at the small scale. Basically, because of grain size and size of the features. I put a reference to the paper from TI about reliability, there is a paragraph on hinge fatigue. 128.178.19.139 (talk) 09:27, 16 April 2012 (UTC)[reply]

Graphic[edit]

I have a hard time picturing the scene; I think a graphic would really help a lot here.

Each [mirror] is mounted on a yoke which in turn is connected to two support posts by compliant torsion hinges. In this type of hinge, the axle is fixed at both ends and literally twists in the middle. [...] Two pairs of electrodes on either side of the hinge control the position of the mirror by electrostatic attraction. One pair acts on the yoke and the other acts on the mirror directly.

So each end of the yoke is connected with a torsion hinge to a support post, and the mirror is mounted on the middle of the yoke? On either side of the hinge we have two pairs of electrodes; does that mean we have eight electrodes per hinge, and since we have two hinges per yoke, overall 16 electrodes per mirror? Thanks, AxelBoldt 05:40, 30 August 2006 (UTC)[reply]

Here's one I found on Google images. There are four electrodes per mirror. The green pair acts on the mirror, the brown pads at the bottom act on the yoke. --Dtcdthingy 19:45, 30 August 2006 (UTC)[reply]

[1] is a paper by the inventor with a good 3d image. --195.137.93.171 (talk) 15:30, 19 July 2011 (UTC)[reply]

Added diagram based on the above references. Egmason (talk) 21:01, 9 February 2012 (UTC)[reply]

Physics News Update[edit]

Thought you all would like to know that this article was referenced in the current issue of Physics News Update, specifically, issue #797. Erzahler 19:42, 16 October 2006 (UTC)[reply]

EEtimes interview, contains history[edit]

There is an interesting interview with Larry Hornbeck at EETimes. It can be used as a source for much of the historical information. - Davandron | Talk 17:01, 25 January 2007 (UTC)[reply]

DMD description comments[edit]

DMDs have now been built consisting of millions of mirrors (not just hundreds of thousands). The tilt angle of the mirrors is not variational, for a particular device it will have a particular tilt angle, in the text this is unclear. Ilent2 (talk) 08:24, 24 September 2014 (UTC)[reply]

million or millions[edit]

"1973 with Harvey C. Nathanson's (inventor of MEMS c. 1965) use of millions of ... mirrors"

I estimate that in 1973 a DMD for 1250 x 800 Pixel World have been very much. Measurement of device and Single mirror = ? Helium4 (talk) 14:58, 18 November 2023 (UTC)[reply]